WHY UNDERSTANDING ESSENTIAL PLUMBING SKILLS IS IMPORTANT WHEN INSTALLING A BATHTUB

Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub

Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub

Blog Article

Book

Here in the next paragraph you can get a bunch of high-quality content relating to How to Install a Bathtub Yourself.


Installing A Bathtub
Mounting a tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is easily available, the project can relocate easily; if you need to open up a wall surface to remove the old tub and also place the brand-new bathtub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub as well as set in the new one. Ensure you have certified on your own for the task and fit trying it. Instead of employing a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you might need a professional plumber to make tube links.
This write-up will assist you set up a brand-new tub in your shower room if you have currently purchased a brand-new bathtub and don't need to change the setup of your previous water system pipes.
Your devices and material checklist must consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is commonly the situation.
    Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the staying water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
    Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipelines.
    If you need to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, place the faucet in the installing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Secure the faucet in position with the maker supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Mounting the Bathtub


    Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
    The next objective is to ensure that the bath tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the bathtub up until the level checks out degree.
    To mount faucets, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
    Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and additionally check the overflow outlet and also the normal electrical outlet for leaks.
    Ultimately, fix the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it right into its final placement.

    Planning for the Installment


    Firstly, the sustaining framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to avoid stress on the tub.
    Fit the adaptable faucet ports to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its last placement.

    Tiling Around the Tub


    In the area where the bathroom satisfies the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, causing the water to permeate the wall surface between the bath and the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can split fairly early if you do not think about this movement before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    As a fervent person who reads on How to Install a Bathtub Yourself, I imagined sharing that segment was beneficial. Appreciated our entry? Please share it. Help somebody else check it out. I cherish reading our article about How to Install a Bathtub Yourself.


    Emergency? We're ready.

    Report this page